Effects of cutting fluids with nano-silver and borax additives on milling performance of aluminium alloys

Basit Öğe Kaydı
dc.contributor.authorCetin, M. Huseyin
dc.contributor.authorKilincarslan, Sena Kabave
dc.date.accessioned2024-09-29T15:57:40Z
dc.date.available2024-09-29T15:57:40Z
dc.date.issued2020
dc.departmentKarabük Üniversitesien_US
dc.description.abstractThe development of tribological properties of cutting fluids is important to ensure cutting efficiency in metal cutting processes. It is expected that the nano-cuffing fluids obtained using nanoparticles as a tribological agent will provide high tribological performance. In this study, the suspension of borax - ethylene glycol and colloidal suspension of borax - ethylene glycol - nano-silver particles were used as cutting fluid for milling of AA7075 - T6 material and their tribological properties were investigated. The originality of this paper is the improvement of the lubrication function and heat transfer properties of cutting fluids by using borax and nano-silver additives. In the experimental part of the current study, borax was used for lubrication, and nano-silver particles were employed to improve the heat transfer properties of nano-cuffing fluids. Both additives were synthesised using ethylene glycol which has high penetration ability. The prepared cutting fluids were applied to the cutting zone in pulverised form by minimum quantity of lubricant (MQL) technique due to the lower environmental and health impacts. In the experimental section, surface roughness values and cutting forces were measured and analysed according to the response surface method (RSM). Besides, chip morphologies were examined in microscale using SEM and EDX, and the effects of additives were discussed in detail. As a result, it was determined that the silver nano-particle additive reduced the surface roughness up to 13.88 %. However, any sufficient effect reducing the cutting forces was not observed.en_US
dc.description.sponsorshipKBU-BAP [KBU-BAP-18-YL-058]en_US
dc.description.sponsorshipThe authors would like to acknowledge the KBU-BAP office. This work was supported by KBU-BAP (Project ID number: KBU-BAP-18-YL-058).en_US
dc.identifier.doi10.1016/j.jmapro.2019.12.042
dc.identifier.endpage182en_US
dc.identifier.issn1526-6125
dc.identifier.issn2212-4616
dc.identifier.scopus2-s2.0-85076835102en_US
dc.identifier.scopusqualityQ1en_US
dc.identifier.startpage170en_US
dc.identifier.urihttps://doi.org/10.1016/j.jmapro.2019.12.042
dc.identifier.urihttps://hdl.handle.net/20.500.14619/4937
dc.identifier.volume50en_US
dc.identifier.wosWOS:000513922000017en_US
dc.identifier.wosqualityQ2en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherElsevier Sci Ltden_US
dc.relation.ispartofJournal of Manufacturing Processesen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subjectAdditivesen_US
dc.subjectNano-silveren_US
dc.subjectBoraxen_US
dc.subjectEthylene glycolen_US
dc.subjectMillingen_US
dc.subjectAA7075-T6en_US
dc.titleEffects of cutting fluids with nano-silver and borax additives on milling performance of aluminium alloysen_US
dc.typeArticleen_US

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu