Optimization of machining parameters for abrasive water jet drilling of carbon fiber-reinforced polymer composite material using Taguchi method

Basit Öğe Kaydı
dc.authoridALTIN KARATAS, MELTEM/0000-0002-1628-1316
dc.contributor.authorKaratas, Meltem Altin
dc.contributor.authorGokkaya, Hasan
dc.contributor.authorNalbant, Muammer
dc.date.accessioned2024-09-29T16:03:23Z
dc.date.available2024-09-29T16:03:23Z
dc.date.issued2020
dc.departmentKarabük Üniversitesien_US
dc.description.abstractPurpose The aim of this paper is to optimize the machining parameters to obtain the smallest average surface roughness values during drilling of the carbon fiber-reinforced polymer (CFRP) composite material with abrasive water jet (AWJ) and analyze the damage of the delamination. Design/methodology/approach CFRP composite material had been fabricated having fiber orientations frequently used in the aerospace industry (0 degrees/45 degrees/90 degrees/-45 degrees). Three different stand-off distances (1, 2 and 3 mm), three different water pressures (1,800, 2,800 and 3,800 bar) and three different hole diameters (4, 8 and 12 mm) were selected as processing parameters. The average surface roughness values were obtained, and delamination damage was then analyzed using Taguchi optimization. Drilling experiments were performed using the Taguchi L-27 orthogonal array via Minitab 17 software. The signal/noise ratio was taken into account in the evaluation of the test results. Using the Taguchi method, the control factors giving the mean surface roughness values were determined. Analysis of variance was performed using the experimental results, and the effect levels of the control factors on the average surface roughness were found. Findings It was found that water pressure and hole diameter had a higher effect on average surface roughness, while water pressure and stand-off distance were effective on delamination. Originality/value The novel approach is to reduce cost and spent time using Taguchi optimization as a result of AWJ drilling the material in this fiber orientation ([0 degrees/45 degrees/90 degrees/-45 degrees](s), which is often used in the aerospace industry).en_US
dc.description.sponsorshipKarabuk University; Karabuk University Coordinatorship of Research Projects [KBU-BAP-16/2-DR-101]en_US
dc.description.sponsorshipThis research was funded by the Karabuk University. The authors would like to thank the Karabuk University Coordinatorship of Research Projects for their support (Award Number: KBU-BAP-16/2-DR-101).en_US
dc.identifier.doi10.1108/AEAT-11-2018-0282
dc.identifier.endpage138en_US
dc.identifier.issn1748-8842
dc.identifier.issn1758-4213
dc.identifier.issue2en_US
dc.identifier.scopus2-s2.0-85074011586en_US
dc.identifier.scopusqualityN/Aen_US
dc.identifier.startpage128en_US
dc.identifier.urihttps://doi.org/10.1108/AEAT-11-2018-0282
dc.identifier.urihttps://hdl.handle.net/20.500.14619/6044
dc.identifier.volume92en_US
dc.identifier.wosWOS:000508435800001en_US
dc.identifier.wosqualityQ4en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherEmerald Group Publishing Ltden_US
dc.relation.ispartofAircraft Engineering and Aerospace Technologyen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subjectCarbon fiber-reinforced polymer composite materialen_US
dc.subjectAverage surface roughnessen_US
dc.subjectDelaminationen_US
dc.subjectTaguchi optimizationen_US
dc.titleOptimization of machining parameters for abrasive water jet drilling of carbon fiber-reinforced polymer composite material using Taguchi methoden_US
dc.typeArticleen_US

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu