Investigation on hole quality of cutting conditions in drilling of CFRP composite

Basit Öğe Kaydı
dc.authoridYASAR, NAFIZ/0000-0002-1427-1384
dc.authoridKORKMAZ, Mehmet Erdi/0000-0002-0481-6002
dc.contributor.authorYasar, Nafiz
dc.contributor.authorKorkmaz, Mehmet Erdi
dc.contributor.authorGunay, Mustafa
dc.date.accessioned2024-09-29T16:01:09Z
dc.date.available2024-09-29T16:01:09Z
dc.date.issued2017
dc.departmentKarabük Üniversitesien_US
dc.description21st Innovative Manufacturing Engineering and Energy International Conference (IManE and E) -- MAY 24-27, 2017 -- Iasi, ROMANIAen_US
dc.description.abstractSurface damages and delamination occurred in drilling of the carbon fiber reinforced polymer composite materials, which change depending on their physical and mechanical properties and cutting conditions, and so affect the hole quality. Therefore, it is requires to be selective with regards to drill geometry and drilling parameters during drilling of CFRP. This study investigated the effects of cutting parameters and drill geometry on the hole quality in terms of hole diameter and surface roughness during the drilling of CFRP composite laminate. Drilling experiments were performed with three different levels of drilling parameters that are point angle, cutting speed and feed rate. At the end of the drilling tests, it has determined that if the feed rate increases, the surface roughness value increases while the hole diameter decreases. The feed rate was determined as the most important parameter with a PCR of 78.02% according to analysis of variance. The better hole quality was obtained with 130 degrees drill among the three drill geometry.en_US
dc.description.sponsorshipGheorghe Asachi Tech Univ Iasi, Dept Machine Mfg Technolen_US
dc.description.sponsorshipScientific Research Project Unit of Karabuk University [KBU-BAP-15/2DR-022]en_US
dc.description.sponsorshipThis study is supported by Scientific Research Project Unit of Karabuk University (KBU-BAP-15/2DR-022) and the authors express their appreciation for this support.en_US
dc.identifier.doi10.1051/matecconf/201711201013
dc.identifier.issn2261-236X
dc.identifier.scopus2-s2.0-85023616481en_US
dc.identifier.scopusqualityN/Aen_US
dc.identifier.urihttps://doi.org/10.1051/matecconf/201711201013
dc.identifier.urihttps://hdl.handle.net/20.500.14619/5534
dc.identifier.volume112en_US
dc.identifier.wosWOS:000579349600013en_US
dc.identifier.wosqualityN/Aen_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherE D P Sciencesen_US
dc.relation.ispartof21st Innovative Manufacturing Engineering & Energy International Conference - Imane&E 2017en_US
dc.relation.publicationcategoryKonferans Öğesi - Uluslararası - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/openAccessen_US
dc.subjectFiber-Reinforced Plasticsen_US
dc.subjectDelamination Analysisen_US
dc.subjectSpeeden_US
dc.subjectParametersen_US
dc.subjectDamageen_US
dc.titleInvestigation on hole quality of cutting conditions in drilling of CFRP compositeen_US
dc.typeConference Objecten_US

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu