APPLICATION OF THE TAGUCHI METHOD TO OPTIMIZE THE CUTTING CONDITIONS IN HARD TURNING OF A RING BORE
dc.authorid | BOY, MEHMET/0000-0003-2471-8001 | |
dc.contributor.author | Boy, Mehmet | |
dc.contributor.author | Ciftci, Ibrahim | |
dc.contributor.author | Gunay, Mustafa | |
dc.contributor.author | Ozhan, Feridun | |
dc.date.accessioned | 2024-09-29T16:06:28Z | |
dc.date.available | 2024-09-29T16:06:28Z | |
dc.date.issued | 2015 | |
dc.department | Karabük Üniversitesi | en_US |
dc.description.abstract | This paper is focused on optimizing the cutting conditions for the surface roughness, inner-diameter error and roundness obtained in hard turning of an inner ring bore. The hard-turning experiments were conducted on hardened and tempered AISI 52100 bearing rings using the L9 orthogonal array on a CNC lathe. The cutting speed, feed rate and number of the machined part were selected as control factors. The optimum cutting conditions were determined using the signal-to-noise (SIN) ratio. S/N ratios were calculated using the lower-the-better approach. An analysis of variance (ANOVA) was also employed to determine the level of the effect of the control factors for the surface roughness, inner-diameter error and roundness. The statistical analysis showed that the feed rate was the most significant factor for the surface roughness while the cutting speed was the most significant factor for the roundness and inner-diameter error. Finally, the optimum cutting conditions were further confirmed with confirmation tests. | en_US |
dc.description.sponsorship | Ministry of Science, Industry and Technology, Turkey [00980.STZ.2011-2]; ORS Bearings, Turkey | en_US |
dc.description.sponsorship | The authors would like to thank the Ministry of Science, Industry and Technology, Turkey (00980.STZ.2011-2) and ORS Bearings, Turkey, for the financial support of this study. | en_US |
dc.identifier.doi | 10.17222/mit.2014.246 | |
dc.identifier.endpage | 772 | en_US |
dc.identifier.issn | 1580-2949 | |
dc.identifier.issn | 1580-3414 | |
dc.identifier.issue | 5 | en_US |
dc.identifier.scopus | 2-s2.0-84947722963 | en_US |
dc.identifier.scopusquality | Q3 | en_US |
dc.identifier.startpage | 765 | en_US |
dc.identifier.uri | https://doi.org/10.17222/mit.2014.246 | |
dc.identifier.uri | https://hdl.handle.net/20.500.14619/6845 | |
dc.identifier.volume | 49 | en_US |
dc.identifier.wos | WOS:000362700700016 | en_US |
dc.identifier.wosquality | Q4 | en_US |
dc.indekslendigikaynak | Web of Science | en_US |
dc.indekslendigikaynak | Scopus | en_US |
dc.language.iso | en | en_US |
dc.publisher | Inst Za Kovinske Materiale I In Tehnologie | en_US |
dc.relation.ispartof | Materiali in Tehnologije | en_US |
dc.relation.publicationcategory | Makale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanı | en_US |
dc.rights | info:eu-repo/semantics/openAccess | en_US |
dc.subject | diameter error | en_US |
dc.subject | hard turning | en_US |
dc.subject | roundness | en_US |
dc.subject | surface roughness | en_US |
dc.subject | Taguchi method | en_US |
dc.title | APPLICATION OF THE TAGUCHI METHOD TO OPTIMIZE THE CUTTING CONDITIONS IN HARD TURNING OF A RING BORE | en_US |
dc.type | Article | en_US |