An investigation on failure behaviour of bonded polylactic acid adherends produced by 3D printing process: experimental and numerical approach

dc.authoridoz, ozkan/0000-0002-9833-429X
dc.authoridOzturk, Fatih Huzeyfe/0000-0001-8025-8236
dc.contributor.authorOz, Ozkan
dc.contributor.authorOzturk, Fatih Huzeyfe
dc.date.accessioned2024-09-29T15:54:47Z
dc.date.available2024-09-29T15:54:47Z
dc.date.issued2023
dc.departmentKarabük Üniversitesien_US
dc.description.abstractThis study investigated the failure behaviour of adhesive bonded single lap joints (SLJs) of Poly (lactic acid) (PLA) adherends fabricated by 3D printing. Adherend printing angle (0 & DEG;, 45 & DEG; and 90 & DEG;) adherend thickness (2, 4 and 6 mm), and overlap length (12.7 and 25.4 mm) were chosen as joint design parameters. In addition to the experimental study, a 3D nonlinear finite element (NL-FE) analysis was performed to determine the variation of stress components in adhesive layer and the numerical failure load of SLJs. The material properties of adherends with different printing angles were defined using Hill yield criterion (HYC). The present study could be considered a novel one given that it presents an anisotropic yield criterion to evaluate the failure of adhesive bonded joints with printed adherends. An analytical expression was also derived to calculate the tensile stiffness of joints. Results obtained from the experimental tests and analytical expression indicated that increasing the adherend thickness, the overlap length, and the printing angle increased the strength and the tensile stiffness of joints, respectively. It was found that the combined effect of printing angle and adherend thickness on joint strength is more prominent for SLJs with overlap length of 25.4 mm. The highest printing angle of 90 & DEG; gave an 85.26% improvement in the failure load when the adherend thickness was increased from 2 to 6 mm for this group of SLJs. The accuracy of NL-FE model based on the HYC was evaluated by comparing the numerical failure loads and failure types with those from the corresponding experiments. NL-FE analyses proved that the HYC could capture the effect of joint design parameters on the strength of the SLJs.en_US
dc.identifier.doi10.1007/s40430-023-04321-8
dc.identifier.issn1678-5878
dc.identifier.issn1806-3691
dc.identifier.issue8en_US
dc.identifier.scopus2-s2.0-85164183780en_US
dc.identifier.scopusqualityQ2en_US
dc.identifier.urihttps://doi.org/10.1007/s40430-023-04321-8
dc.identifier.urihttps://hdl.handle.net/20.500.14619/4284
dc.identifier.volume45en_US
dc.identifier.wosWOS:001025019400003en_US
dc.identifier.wosqualityQ3en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherSpringer Heidelbergen_US
dc.relation.ispartofJournal of the Brazilian Society of Mechanical Sciences and Engineeringen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subject3D printingen_US
dc.subjectAdhesive bonded jointen_US
dc.subjectFinite element analysisen_US
dc.subjectMechanical testingen_US
dc.titleAn investigation on failure behaviour of bonded polylactic acid adherends produced by 3D printing process: experimental and numerical approachen_US
dc.typeArticleen_US

Dosyalar